AFP0HC32EP PLC & HMI by Panasonic
| Status: | Unknown |
|---|---|
| Series: | - |
| RoHS: | Unknown |
Specifications
| Number of Controllable I/O Points | 32 points (Input: 16, Output: 16), When expanded: Max. 384 points |
|---|---|
| Programming Method/Control Method | Relay symbol / Cyclic operation |
| Program Memory | Built-in flash ROM (no backup battery required) |
| Number of Instructions: Basic Instructions | 120 types approx. |
| Number of Instructions: High-Level Instructions | 270 types approx. |
| Program Capacity | 24 k /32 k /40 k / 64 k steps Can be selected at system register No. 0 When the program capacity is changed, the number of words that can be used in the data register (DT) is also changed. Program capacity DT Number of word 24k steps 32k steps(initial value) 40k steps 64k steps 65,533 words 32,765 words(initial value) 24,573 words 12,285 words |
| 24k steps 32k steps(initial value) 40k steps 64k steps | 65,533 words 32,765 words(initial value) 24,573 words 12,285 words |
| Operation Speed | Basic instruction (NOT: /) : 10 ns/step approx. (Up to 10 k steps) ,0.18 μs/step approx. (10 k steps and later) Basic instruction (ST) : 40 ns/step approx. (Up to 10 k steps) ,0.65 μs/step approx. (10 k steps and later) High-level instruction (FOMV) : 0.14 μs/step approx. (Up to 10 k steps) , 1.2 μs/step approx. (10 k steps and later) |
| Base Scan Time I/O Refresh And Base Time | Control unit: 100 μs or less approx. and FP0 / FP0R expanshion unit refresh time (Note) Note : Refresh times for FP0 / FP0R expansion units 8 points unit : Number of units×0.8ms 16 points unit : Number of units×1.0ms 32 points unit : Number of units×1.3ms 64 points unit : Number of units×1.9ms |
| Operation Memory: Relay: External Input (X) | 1, 760 points (X0 to X109F)(Note 1, 2) Note 1 : The number of points that can be used depends on the combination of hardware. Note 2 : Some specifications are compatible with FPΣ. |
| Operation Memory: Relay: External Output (Y) | 1, 760 points (X0 to X109F)(Note 1, 2) Note 1 : The number of points that can be used depends on the combination of hardware. Note 2 : Some specifications are compatible with FPΣ. |
| Operation Memory: Relay: Internal Relay (R) | 8,192 points (R0 to R511F) (Note 1) Note 1 : Some specifications are compatible with FPΣ. |
| Operation Memory: Relay: Special Internal Relay (R) | 800 points (R9000 to R951F) |
| Operation Memory: Relay: Timer/Counter (T/C) | 1,024 points (initial setting, timer: 1,008 points, counter: 16 points)(Note) Note : An auxiliary timer instruction (F137) can be used to add the number of points. |
| Operation Memory: Relay: Link Relay (L) | 2,048 points (L0 to L127F) |
| Operation Memory: Memory Area: Data Register (DT) | 12,285 words or 24,573 words or 32,765 words or 65,533 words(Note) Note : System register No. 0 (program capacity) can be configured to select the capacity of the data register (DT). |
| Operation Memory: Memory Area: Special Data Register (DT) | 1,000 words (DT90000 to DT90999)(Note) Note : Some specifications are compatible with FPΣ. |
| Operation Memory: Memory Area: Link Data Register (LD) | 256 words (LD0 to LD255) |
| Operation Memory: Memory Area: Index Register (A) | 14 words (I0 to ID) |
| Differential Points | Points for the program capacity |
| Number of Master Control Relay (MCR) | 256 points |
| Number of Labels (JP and LOOP) | 256 points |
| Number of Step Ladders | 1,000 stages |
| Number of Subroutines | 500 subroutines |
| Number of Interrupt Program | 9 programs •Input: 8 programs (INT0 to INT7) •Periodic: 1 program (INT24) |
| Sampling Trace | Available(Note) [Sampling by commands / Sampling at regular time intervals (For one sampling: 16 bits + 3 words), 1,000 samples] Note : Logging trace and sampling trace cannot be used at the same time. |
| Comment Storage | I/O comments, remarks and block comments can be stored. (no backup battery required, 1 M byte) |
| PLC Link Function (Serial Communication) | Max. 16 units, link relays: 1,024 points, link registers: 128 words. (Data transfer and remote programming are not supported) |
| Password | Available (32 digits) |
| Program Upload Protection | Available |
| Program Protect Function | Available |
| Self-Diagnosis Function | Watchdog timer, program syntax check, etc. |
| Program Edition During Run | Available |
| SD Memory Card Function | SD memory card project copy, SD memory card access instruction, Logging trace function (Note) Note : Logging trace and sampling trace cannot be used at the same time. |
| Memory Transfer | Available [Built-in memory (ROM ⇔ RAM)] |
| High Speed Counter: Main Unit Input | Single-phase 4 channels (Max. 100 kHz each input) or 2-phase 2 channels (Max. 50 kHz each input)(Note) Note : The specifications are based on the rated input voltage of 24 V DC at +25 ℃ +77 ℉ . The maximum operation frequency may be lower depending on the applied voltage, ambient temperature, and conditions of use. The maximum operation frequency varies depending on how the unit is used. |
| Pulse Output: Main Unit Output | 4 channels (Max. 100 kHz each axis)(Note) Note : The specifications are based on the rated input voltage of 24 V DC at +25 ℃ +77 ℉ . The maximum operation frequency may be lower depending on the applied voltage, ambient temperature, and conditions of use. The maximum operation frequency varies depending on how the unit is used. |
| PWM Output: Main Unit Output | 4 channels (1 Hz to 70 kHz: 1,000 resolution / 70.001 kHz to 100 kHz: 100 resolution(Note) Note : The specifications are based on the rated input voltage of 24 V DC at +25 ℃ +77 ℉ . The maximum operation frequency may be lower depending on the applied voltage, ambient temperature, and conditions of use. The maximum operation frequency varies depending on how the unit is used. |
| Pulse Catch Input Interrupt Input | Total 8 points (with high speed counter) |
| Periodical Interrupt | 0.1 ms to 30 sec. |
| Potentiometer (Volume) Input | Not available |
| Real Time Clock | Year (last two digits), month, day, hour (24-hour display), minute, second and day of week(Note 1, 2) Note 1 : Accuracy of the clock / calendar (within ± 90 seconds per month at +25 ℃ +77 ℉ ).If an error of the clock / calendar becomes a problem in the system, set an accurate time periodically. Note 2 : If the battery is not attached, calendar information is cleared when the power is turned off. It will be necessary to set the date when the power is turned on. |
| Memory Backup: Backup by Instruction P13 | Data register: all area(Note) Note : Data can be rewritten up to 10,000 times. Hold / non-hold areas can be specified in the system registers. |
| Memory Backup: Auto-Backup at Power Failure | Counter: 16 points Internal relay: 128 points Data register: 315 words Note : Data can be rewritten up to 10,000 times. Hold / non-hold areas can be specified in the system registers. |
| Battery backup (only when a battery is installed) | Hold areas or non-hold areas can be specified by setting the system registers No.6 to No. 13. (It is also possible to make the setting for hold all points.) |
| Battery Life | 5 years or more under a production condition (operates for 8 hours per day) |
| CE Marking Directive Compliance | EMC Directive, RoHS Directive |
| Rated Voltage | 24 V DC |
| Operating Voltage Range | 20.4 to 28.8 V DC |
| Current Consumption | 170 mA or less |
| Allowed Momentary Power Off Time | 4 ms (at 20.4 V DC), 10 ms (24 V DC or higher) |
| Operating Temperature | 0 to +55 ℃ +32 to +131 ℉ , At storage: -40 to +70 ℃ - 40 to +158 ℉ |
| Operating Humidity | 10 to 95 % RH (at +25 ℃ +77 ℉ , no dew condensation allowed), At storage: 10 to 95 % RH (at +25 ℃ +77 ℉ , no dew condensation allowed) |
| Withstand Voltage | (Detection current: 5 mA) 500 V AC for 1 minute Input and output terminals ⇔ power and functional ground terminals Input terminals ⇔ Output terminals |
| Insulation Resistance | (Test voltage: 500 V DC) 100 MΩ or more Input and output terminals ⇔ power and functional ground terminals Input terminals ⇔ Output terminals |
| Vibration Resistance | 5 to 8.4 Hz, single amplitude of 3.5 mm 0.138 in, 8.4 to 150 Hz, constant acceleration of 9.8 m/s2, for 10 times each in X, Y, and Z directions (1 octave/min.) (JIS B 3502, IEC 61131-2) |
| Shock Resistance | 147 m/s2, 4 times each in X, Y, and Z directions (JIS B 3502, IEC 61131-2) |
| Noise Immunity | 1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator) (Power supply terminal) |
| Operating Environment | Free from corrosive gasses and excessive dust |
| Overvoltage Class | Category II |
| Pollution Level | Pollution level 2 |
| Net Weight | 130 g approx. |
| Interface | RS-232C, three-wire system, 1 channel (Not insulated) |
| Transmission Distance | 15 m 49.213 ft |
| Configuration | 1 : 1 communication |
| Communication Method | Full duplex / Half-duplex system |
| Synchronous Method | Start-stop synchronization system |
| Transmission Cable | Multi-conductor shielded wire |
| d (Specified at the system registers) | 1,200(Note), 2,400(Note), 4,800, 9,600, 19,200, 38,400, 57,600, 115,200, 230,400 bits/sec. Note : System register no. 415 cannot be used to set the baud rate to 1,200 bps. To set the baud rate to 1,200 bps, use the SYS1 instruction. If the baud rate of any of the COM ports is 2,400 bps or lower, F-ROM access will slow down. Example) F12(ICRD) instruction, P13(ICWT) instruction, etc. |
| Transmission Format: Data Length | 7 bits / 8 bits |
| Transmission Format: Parity | none / odd / even |
| Transmission Format: Stop Bit | 1 bit / 2 bits |
| Transmission Format: Start Code | with STX / without STX |
| Transmission Format: End Code | CR / CR + LF / none / ETX / Time (0 to 100.00 ms) |
| Data Transmission Order | Transmit from bit 0 in character units |
| Communication Mode | MEWTOCOL-COM (Master / Slave) (Computer link) General-purpose communication PLC link MODBUS RTU (Master / Slave) |
| Remark | The start and end codes can be used only for general-purpose serial communications. The unit No. (station number) can be selected at system register No. 410. |
| Communication Interface | Ethernet 100BASE-TX / 10BASE-T |
| Communication Speed | 100 Mbps, 10 Mbps auto negotiation function |
| Total Cable Length | 100 m 328.084 ft (500 m 1640.420 ft when a repeater is used) |
| Ber Of Simultaneous Connections | Max. 10 (system connection: 1, user connection: 9) |
| Communication Protocol (Communication Layer) | TCP / IP, UDP |
| DNS | Supports name servers |
| DHCP | Automatic IP address acquisition |
| FTP server/Client | File transmission, server function, No. of users:1 Client function, Data file transfer |
| SNTP | Time adjustment function |
| General-Purpose Communication | 4 kB / 1 connection (user connection: 1 to 9) (Note) Note : General-purpose communications can be up to 4 kB (reception) and up to 2 kB (transmission) per connection. |
| Dedicated Communication | EtherNet/IP MEWTOCOL-COM (Master / Slave) (Computer link) MODBUS-TCP (Master / Slave) MEWTOCOL-DAT (Master / Slave) General-purpose communication MC protocol (Note 1) (Master / Slave) Note : MC protocol is a short form denoting MELSEC communication protocol; MELSEC is a registered trademark of Mitsubishi Electric Corporation.QnA compatible 3E frame, only binary (bulk writing and bulk reading) use is available. |
| Standard | USB2.0 Full speed (USB mini B type) |
| Communication Function | Computer link (slave) |
| :5V | Connecting programmable display model : For 5 V DC type GT02 series Programmable Display |
| Rated Input Voltage | 24 V DC |
| Applied Voltage Range | 21.6 to 26.4 V DC |
| Rated Input Current | High-speed part (X0 to X7) : 8 mA approx. Low-speed part (X8 to XF) : 3.5 mA approx. |
| Output Points Per Common | 16 points/common (Y0 to YF / 1 common) |
| Min. On Voltage/Min. On Current | High-speed part (X0 to X7) : 19.2 V DC / 6 mA Low-speed part (X8 to XF) : 19.2 V DC / 3 mA |
| Max. Off Voltage/Max. Off Current | 2.4 V DC / 1 mA |
| Input Impedance | High-speed part (X0 to X7) : 3 kΩ approx. Low-speed part (X8 to XF) : 6.8 kΩ approx. |
| Response Time: OFF→ON | High-speed part (For Y0, Y1, Y3, Y4, Y8, Y9, YB, YC) : 2 μs or less, Low-speed part (For Y2, Y5, Y6, Y7, YA, YD, YE, YF) : 1 ms or less |
| Response Time: ON→OFF | High-speed part (For Y0, Y1, Y3, Y4, Y8, Y9, YB, YC) : 5 μs or less, Low-speed part (For Y2, Y5, Y6, Y7, YA, YD, YE, YF) : 1 ms or less |
| Action Indicator | LED display |
| Output Type | Pch open drain |
| Rated Load Voltage | 24 V DC |
| Load Voltage Allowable Range | 21.6 to 26.4 V DC |
| Rated Load Current | 0.3 A (For Y0 to YF) |
| Max. Surge Current | High-speed part (For Y0, Y1, Y3, Y4, Y8, Y9, YB, YC) : 1.0 A, Low-speed part (For Y2, Y5, Y6, Y7, YA, YD, YE, YF) : 0.5 A |
| FF State Leakage Current | 2 μA or less |
| N State Voltage Drop | 0.5 V DC or less |
| Overcurrent Protection | Provided (automatically protected for each 8 points) |
| Surge Absorber | Zener diode |
| Rating Mode Indicator | LED display |
Last 6 months Inventory & Pricing History
Alternative Descriptions
| Automation module: PLC programmable controller | TME |
| PLC, 16 IN 16 OUT, ETHERNET RS232C, FP0H SERIES | RS Americas |
| Fp0H Cpu: 16 16 Pnp, 4 Axis 100Khz, Ethernet/Ip, Sd, rs232, Usb |Panasonic AFP0HC32EP | Newark Electronics |
Frequently Asked Questions
Where can I find additional details, specifications and documents for a AFP0HC32EP?
Additional datasheets, footprints and schematics for AFP0HC32EP are listed on our Part Details page. You can also find images and similar parts to AFP0HC32EP on this page.
What pricing and inventory information can I view?
Distributor pricing and stock information is available for AFP0HC32EP on our Product Comparison page. Access via the 'View Pricing & Stock' button to view AFP0HC32EP price breaks, MOQs, lead times, inventory and SKUs from distributors.
What category does AFP0HC32EP fall under?
The AFP0HC32EP is listed under Industrial Automation > PLC & HMI > Programmable Logic Controllers / Interface Terminal > FP0H Series.
Can I view similar or alternative parts?
You can view similar parts to AFP0HC32EP when available in the FP0H Series range under the specifications section at the bottom of the details page.
Who can I contact for technical support of the product?
Submit any questions directly to the customer support team of the distributor listing the product. For the AFP0HC32EP you can contact the distributor directly for product support, shipping queries etc.
Is the AFP0HC32EP RoHS compliant?
This part has not been flagged as RoHS Compliant.
Which authorised distributors for AFP0HC32EP have stock available?
Authorised distributors including Ozdisan, TME, RS Americas and Newark Electronics have stock available or on a lead time for AFP0HC32EP.
How do I check stock and lead times for all distributors?
Stock availability and lead times will be displayed for AFP0HC32EP often in real-time on the comparison pages.
What if I can't find stock of AFP0HC32EP?
You can fill out our help required form which you can use to request a quote for AFP0HC32EP from some of our verified obsolescence suppliers. Alternatively, contact us via our web chat in the bottom left of your screen and one of our team will try to help.